Here you can choose all the components of a BRV heat
distribution system on one web page, just tick the items you need and then
click on “ADD TO CART”
Efficient heating systems are hugely effected by how
heating is distributed throughout the building, Evergreen Energy now offer the best
in heating distribution systems from BRV (market leader in Italian heating
distribution systems).
The new BRV pump units are now supplied in a number of
different configurations including systems that are equipped with modern
climatic controllers to allow an optimal balance between comfort, safety and
energy saving. The functionality and efficiency too, have been taken into
account with regards to the installation stage. All products that are equipped
with integrated controllers (Heating or Solar) are prewired: temperature
sensors, power supply and control cables, thermostats and remote controls. Real
Plug and Play
Zone Distribution
Header
Distribution headers for heating systems are made from
electro-welded steel and pipe and are suitable for power up to 70kW’s. EPS 25mm
thermal insulation according to DIN 4102-82 with a galvanised steel cover 0.8mm
thick. Tested to 12 bar. Available in many different zone sizes.
Hydraulic
Switcher Unit
|
|
Hydraulic switcher unit with insulation, to beconnected below the distribution manifold. This device allows the primary and secondary
circuits to be disconnected hydraulically, thereby giving allowing greater
volumetric flow in the manifold in comparison to the boiler flow.
This isparticularly suitable for use with condensing boilers. In fact if the boiler
pump is set correctly this unit can ensure a low water return temperature
(always below 57°C – this is the condensing temperature of the steam in methane
gas) so increasing the efficiency of the whole installation
|
Security
Unit
|
|
Security
unit with 20mm EPS insulation, comes with 1” female connection on bottom, Includes:
- Forged brass body
- Manometer Ø 63mm
- Auto air vent, 6 bar
- 3 Bar safety valve
|
M2 insulated
heating pump group
|
|
Fits directly onto the heating manifold and circulates unmixed heating fluid (for example to heat a hot water cylinder), includes:
Flow Side
- Swivel 1” connection
- Flanged ball valve DN20 with T handle
- Flanged ball valve DN20, provided with thermometer holder handle (red-ring thermometer, 0°C to
120°C).
Return Side
- Flanged ball valve DN20 with non return valve 20 mbar (which can be
over-ridden by rotating the handle by 45°) provided with thermometer holder
handle (blue-ring thermometer, 0°C to 120°C).
- Swivel 1” connection
|
M2
FIX3 (F4) insulated heating pump group
|
|
Fits directly onto the heating manifold and circulates mixed heating fluid using a
thermostatically controlled mixing valve, includes:
Flow Side
- Swivel 1” connection
- Thermostatic mixing valve with a setting range from 35°C to 60°C
- Flanged ball valve DN20, provided with thermometer holder handle (red-ring thermometer, 0°C to
120°C).
Return Side
- Flanged ball valve DN20 with non return valve 20 mbar (which can be
over-ridden by rotating the handle by 45°) provided with thermometer holder
handle (blue-ring thermometer, 0°C to 120°C).
- T connection for mixing valve
- Swivel 1” connection
|
M2 MIX3
insulated heating pump group
|
|
Fits directly onto the heating manifold and circulates mixed heating fluid using an electronic
controlled mixing valve that connects back to boiler heating system or climatic
controller (suitable for use with weather compensating systems), includes:
Flow Side
- Swivel 1” connection
- 3 – way mixing valve with electronic actuator
- Flanged ball valve DN20, provided with thermometer holder handle (red-ring thermometer, 0°C to
120°C).
Return Side
- Flanged ball valve DN20 with non return valve 20 mbar (which can be
over-ridden by rotating the handle by 45°) provided with thermometer holder
handle (blue-ring thermometer, 0°C to 120°C).
- T connection for mixing valve
- Swivel 1” connection
|
Climatic
Controller
|
|
Climatic
controller with 6 different programs to manage 1 mixed heating circuit
(circulating pump contact and contacts to open and close motorized mixing
valve), 1 unmixed circuit, 1 heat source with buffer logic.
- 6inputs for PT 1000 sensors: Outside sensor, mixed circuit flow temperature,
unmixed circuit flow temperature, boiler temperature (optional), room
temperature (optional), remote control (optional).
- 4output relays 230V: Mixed circuit circulating pump, open mixing valve, close
mixing valve, unmixed circuit circulating pump
- 1output with zero-potential for boiler call
- 1outside temperature sensor
- 1pipe sensor
- 1dip sensor
|
Please Choose:
Zone Manifold
This product was added to our catalog on Thursday 29 April, 2010.
